Intergrinding
Clinker, gypsum and trass are ground together in the same mill.
- Advantage
- A homogeneous mix is obtained.
- Point to watch
- Clinker is harder than trass, so controlling the particle size distribution in one mill is difficult.

What is trass?
Trass is a natural pozzolan of volcanic origin that improves the durability of cement. This page summarizes what it is, how it works in cement, how trass cement is produced and where it is preferred.
Pozzolans are siliceous and aluminous materials that have no binding ability on their own. When finely ground, mixed with cement or lime and brought into contact with water, they combine with calcium hydroxide to form binding compounds.
Pozzolans fall into two groups, natural and artificial. Trass is the common name for the volcanic tuff type of natural pozzolan. In practice, most natural pozzolans are also called “trass”.
Cements that contain natural pozzolan above the proportion set in the standards are called “trass cement”.
Trass puts to use a by-product that is left over when cement reacts with water.
The main minerals of Portland cement form strength-giving compounds during hydration.
The same reaction produces Ca(OH)₂, which dissolves easily in water. It adds nothing to strength; when it leaches out it can leave voids in the concrete and is open to harmful attack.
The reactive silica and alumina in trass combine with Ca(OH)₂. This reaction is called the pozzolanic reaction.
Additional calcium silicate hydrate (C-S-H) gel forms, filling the pores; concrete becomes tighter and more durable over time.
In short, trass turns the useless by-product of cement into binder.
Trass is turned into cement with clinker and gypsum in one of two ways.
Clinker, gypsum and trass are ground together in the same mill.
Clinker–gypsum and trass are ground separately, then blended.
In practice intergrinding is more common. Because grinding trass to a given fineness takes less energy than grinding clinker, energy use per tonne falls noticeably as the substitution rate rises.
The properties below describe the general behaviour of trass cements; they vary with particle size, substitution rate and conditions of use.
Less heat is released during setting; the risk of thermal stress in mass concrete falls.
A slower rise in temperature reduces the risk of thermal cracking.
C-S-H filling the pores makes the concrete less permeable.
The risk of expansion and cracking from alkali-silica reaction is reduced.
More durable in sulfate-bearing soils and waters.
Good resistance to chlorides and other salts.
The dense structure helps slow the ingress of carbon dioxide into the concrete.
Low permeability makes it harder for water and chlorides to reach the reinforcement.
The pozzolanic reaction continues over time; at later ages strength can match or exceed Portland cement.
Fresh concrete is generally more workable than with Portland cement.
Shrinkage behaviour is similar to Portland cement.
It can be used almost anywhere Portland cement is used. It is especially advantageous in the following areas.
Resistance to aggressive waters and a plastic consistency.
Protection against chemicals such as nitrogen, ammonium and sulfate.
Low heat release during setting in dams and heavy foundations.
A smooth, uniform surface thanks to fine grinding.
Contributes fineness, tensile strength and airtightness.
Bridges, dams, ports, breakwaters and quays.
Low permeability delays rusting of the reinforcement.
Technical data
The values below will be filled in from the company's laboratory analysis reports.
| Chemical composition | Value |
|---|---|
| SiO₂ | To be added |
| Al₂O₃ | To be added |
| Fe₂O₃ | To be added |
| CaO | To be added |
| MgO | To be added |
| SO₃ | To be added |
| Loss on ignition | To be added |
| Pozzolanic activity | Value |
|---|---|
| Pozzolanic activity index (7 days) | To be added |
| Pozzolanic activity index (28 days) | To be added |
| Product grades | Value |
|---|---|
| Grade name and grain size range | To be added |
| Physical properties | Value |
|---|---|
| Fineness (Blaine) | To be added |
| Specific gravity | To be added |
| Moisture | To be added |
| Particle size distribution (sieve analysis) | To be added |
Values are published together with the report of the laboratory that ran the analysis.